Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
Listed here in the next paragraph you can get lots of outstanding help and advice involving Installing A Bathtub.
Installing a tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old tub is easily available, the project can relocate rapidly; if you have to open a wall surface to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the task as well as fit attempting it. Instead of hiring a professional to take over a halfway-completed job, it is far better to think about using one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will aid you set up a brand-new tub in your bathroom if you have actually currently acquired a new bathtub as well as don't require to alter the setup of your previous water pipelines.
Your tools and also product list need to consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be fairly troublesome because of the limited accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning during this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washers are in place in between the faucet and the sink. Safeguard the tap in place with the maker provided backnut. As soon as the tap is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Making use of the two wooden boards under its feet, place the tub in the required setting. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the bathtub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water system and also inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bathtub needs to wait till the bathtub has actually been utilized at the very least once as this will certainly settle it right into its last setting.
Preparing for the Installation
To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, bring about complications with moisture as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the tub with water before securing, to enable the activity experienced when the bathtub remains in use. The sealer can crack rather very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is advisable to fit the ceramic tiles making use of waterproof or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that write up about How to Install a Bathtub Yourself while looking around the internet. Appreciated our posting? Please share it. Let another person discover it. Thank you for taking the time to read it.
We're on standby! Report this page